2019-2024 Ram 3500 Diesel 4WD 4.5'' Coil Spring Lift Kit

All-new 2019-2024 Ram 3500 4WD HD 4.5" lift kit 

4.5-inch front with rear blocks lift kit

Includes all-new transfer case clocking ring and new heavy-duty transmission crossmember.

Includes 4 Falcon 1.1 Monotube shocks tuned specifically for the Ram 3500 HD.

For use on Diesel engine Ram 3500 4WD HD trucks only.

Allows for up to 37x13.50 tires on 20" x 9" wide wheels with -18 offset.

Note: Does not work with Factory Air suspension, Auto Level system (factory helper bags) HEMI Gasoline engine, dually models, Classic models, and any automatic-leveling rear air suspension models.  Single Cab configuration has not been validated for fitment & drivability by ReadyLIFT.  

Special Note RAM TSB 03-003-23:  Symptom/Vehicle Issue: Ratchet Type Click, Clicking Noise Heard In Four Wheel Drive (4WD) While Turning. Download TSB Info.  Recommended driveline for the 68RFE Adams Drive Shaft SKU:ASDRAM-1350F-5GEN. 

• The all-new 4.5" Coil Spring Lift Kits allow for even more ground clearance while going to a 37" tire.  Springing up to the new 4.5" lift yields all the bells and whistles of a big 6" kit but at a slightly lower, garage-able stance.  These kits come with heavy-duty steel radius arm drop brackets, heavy-duty fabricated steel front track bar brackets, forged dropped pitman arm, sway bar relocation brackets, and bump stop extensions preventing over-compression of the included Falcon 1.1 Monotube front & rear shocks.  The 4.5" Ram HD kit includes our unique CNC-machined 6061-T6 billet Aluminum Driveline Indexing System (DIS) that re-clocks the transfer case to properly align the front output shaft for improved driveline angles.  The Ram 3500 HD comes with a high-output diesel engine DIS system. 
  

  
  

  Kit 49-19430 includes the new DIS re-positioning components, heavy-duty and great riding 4.5" lift front springs, 3" lift rear taper blocks, heavy-duty radius arm drop brackets, heavy-duty fabricated steel front, track bar brackets, dropped cast iron pitman arm, front/rear sway bar relocation brackets, and bump stop extensions preventing over-compression of the new Falcon 1.1 Monotube front/rear shocks.

  
  

  *Kit will not fit any models with the standard output 6.7L diesel motor, HEMI Gasoline engine, dually models, Classic models, and any automatic-leveling rear air suspension models.

  Tire Fitment

  • Maximum fitment: 37x12.50 tire

    20'' x 9" wide wheel -18 offset

    Tire Size Note: ReadyLIFT wheel and tire fitment recommendations are typically based on Wheel Pros wheels and Nitto tires. Due to product differences among tire manufacturers, tire specifications and dimensions including, but limited to, overall diameter, rolling diameter, tread width, aspect ratio, lug pattern, sidewall construction and inflation pressure, will vary meaningfully by tire and wheel manufacturer. Every tire and wheel combination should be test fit prior to installation. Consult your local installer to learn more about the right tire fitment for your application.

    Ride Quality Note: When lifting a vehicle and installing aftermarket wheels and tires, a tire manufacturer's construction and material quality can alter vehicle ride quality. When increasing a vehicle wheel and tire size, most larger aftermarket truck and SUV tires are 10-ply (or more) E tires compared to typical OEM 6-ply C tires. This more rigid sidewall construction increases the perception of suspension stiffness often described as ride harshness. The ride, handling, traction, noise, fuel economy, and wear differences between All-Season, All-Terrain, Mud-Terrain, or Trail-Terrain type tires can be significant. Please take into account tire and wheel choice will generally have a meaningful impact on the ride & handling experience.

    Kit Components

    4.5" Front Lift Spring

    3-Inch Fabricated Block

    19-21 Ram 3500 U-Bolt for 4.5-Inch Kit

    Falcon Shock, Front

    Falcon Shock, Rear

    Radius Arm Drop, Driver

    Radius Arm Drop, Passenger

    Front Track Bar Bracket

    Driver, Sway Bar Drop Bracket

    Passenger, Sway Bar Drop Bracket

    Replacement Front Bump Stop

    Rear Bump Stop Extension

    Pitman Arm, Drop, Replacement

    Transmission Connector Bracket

    Transmission Crossmember

    Transmission Harness Bracket

    Transmission Mounting Plate

    Transmission Mount Spacer

    8 Bolt Clocking Ring

    Front Brakeline Bracket

    Rear Brakeline Bracket

    E-Brake Extension

    Pinch Clamp

    Transfer Case Spacer

    Auto Trans Extension Housing Seal (MOPAR)

    Hardware Pack

    Installation

    SAEJ2492 WARNING: By installing this product, you acknowledge that the suspension of this vehicle has been modified. As a result, this vehicle may handle differently than factory-equipped vehicles. As with any vehicle, extreme care must be used to prevent loss of control or rollover during sharp turns or abrupt maneuvers. Always wear seat belts, and drive safely, recognizing that reduced speeds and specialized driving techniques may be required. Failure to drive this vehicle safely may result in serious injury or death. Do not drive this vehicle unless you are familiar with its unique handling characteristics and are confident of your ability to maintain control under all driving conditions. Some modifications (and combinations of modifications) are not recommended and may not be permitted in your state. Consult your owner's manual, the instructions accompanying this product, and state laws before undertaking these modifications. You are responsible for the legality and safety of the vehicle you modify using these components.

     

    INSTALLATION ALIGNMENT NOTE:  Your vehicle may require alignment after product installation.  You may incur additional costs to align the vehicle.

     

    INSTALLATION HEADLAMP AIM NOTE:  In addition to your vehicle alignment, for your safety and others, it is necessary to check and adjust your vehicle headlamps for proper aim and alignment after product installation.  You may incur additional costs to adjust the headlamp system.

     

    INSTALLATION ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS) NOTE:  If your vehicle is equipped with active or passive safety/collision monitoring and/or assistance/avoidance systems including, but not limited to, camera- or radar/sonar-based systems, check and adjust your vehicle’s systems for proper aim and function after product installation.   In some instances, your vehicle may require OEM dealer service tools and factory-trained technicians to re-calibrate ADAS.  You may incur additional costs to adjust ADAS systems.

    
    

    DO IT YOURSELF: Please read Instructions thoroughly and completely before beginning installation. Installation by a certified mechanic is recommended. ReadyLIFT Suspension Inc. is NOT responsible for any damage or failure resulting from improper installation. Download Pdf Instructions

    Estimated Installation Time: 12 Hours +/- 1 hour (excluding alignment and wheel/tire assembly)

    • California Residents: Prop 65 WARNING

      Falcon Shocks “ The Ultimate Blend of Performance, Quality, and Bang for the Buck
      

      ·         Falcon 1.1 Monotube Shocks deliver increased stability improved ride quality and comfort for a daily-driven vehicle in an economical, compact performance package.

      ·         Falcon 1.1 Monotube Shocks have been optimized for on-road driving with increased stability over stock for driven vehicles on and off road.  High- Value Performance is the driving force behind these vehicle-specific dampers for trucks and SUVs. 

      ·         Falcon 1.1 Monotube Shocks are ideal for daily driven trucks and SUVs as well as the enthusiast wanting a consistent controlled feel through all driving conditions

      ·         Falcon 1.1 Monotube shocks include race-inspired performance, handling, and stability for off-road rigs. Falcon Jeep shock absorbers will significantly increase the chassis performance of any lifted truck or SUV.

      ·         Falcon 1.1 Monotube Shock Specifications

      o   2-1/8" shock body for high-value performance

      o   6061-T6 aluminum alloy billet piston

      o   1/2" induction hardened chrome plated shaft resists rock damage corrosion and shaft buckling

       

      o   Microcellular Foam Progressive Bump Stops (Bump stop configuration varies depending on shock absorber collapsed length, tire size, and fenders.)